Filamento PLA+ Tough Pro AF negro ónix de 1,75 mm ¡Fabricado en EE. UU.!
Filamento PLA+ Tough Pro AF negro ónix de 1,75 mm ¡Fabricado en EE. UU.!
No se pudo cargar la disponibilidad de retiro
Presentamos nuestro nuevo PLA+ TOUGH Pro. Un PLA resistente de calidad de ingeniería que puede soportar fuertes impactos y altas temperaturas. Directamente desde la placa de construcción, nuestro PLA+ Tough Pro le brinda una resistencia al impacto 8,8 veces mayor que un PLA estándar.
Nuestro Tough Pro PLA+ utiliza resina virgen NatureWorks Ingeo 3D870, que fue diseñada para brindar propiedades térmicas y mecánicas similares al ABS en un paquete de PLA ecológico.
Este grado de PLA se puede recocer después de la impresión para cristalizar aún más el material, mejorando aún más sus propiedades térmicas y mecánicas.
Haga clic aquí para ver nuestra guía sobre cómo recocer sus piezas.
Nuestro Tough Pro PLA+ es un material verdaderamente resistente, diseñado para los trabajos más difíciles. Fabricado con resina PLA Ingeo 3D870 diseñada y fabricada aquí mismo en los EE. UU.; después del recocido, tiene una resistencia al impacto comparable al ABS y una resistencia a la temperatura comparable al PETG, todo en un paquete de PLA de base biológica con las mismas excelentes características de impresión 3D del PLA.
Cada carrete contiene 1 kg (2,2 libras) de filamento, con un diámetro de 1,75 mm y una precisión dimensional de +/- 0,05 mm.
Dimensiones del carrete (ahora compatible con las unidades AMS de Bambu Labs):
- Diámetro interior (ID) = 52 mm
- Diámetro exterior (OD) = 200 mm
- Ancho (An) = 67 mm
- Peso = 200 - 220 g
Recomendamos una temperatura de boquilla de 205-220 °C y una temperatura de lecho de 45-60 °C.
Anteriormente, Onyx Black se llamaba Matte Black. Si recibes un carrete con Matte Black en la etiqueta, ¡es el color correcto!
Descargas:
Print Settings
Print Settings
- Nozzle Temperature: 240 - 270°C
- Bed Temperature: 70 - 100°C
- Speed: 60 - 300 mm/s
Nozzle temperature can vary between 240-270°C depending on desired layer to layer adhesion vs part print quality. Higher nozzle temperatures will result in stronger parts, but may cause lower quality and/or increased stringing.
Part cooling can also vary depending on desired layer to layer adhesion vs part print quality. More cooling will result in better overhangs & bridging, but will decrease the ultimate layer to layer adhesion.
For Bambu Printers: We recommend using the Bambu Labs Gold Textured PEI build plate, or other aftermarket textured PEI build plates, for this material. 70°C should be sufficient for adequate build plate adhesion, going higher than this temperature may cause parts to adhere to the plate too well.
For Bambu Printers: recommended retraction length can vary between 0.8-1.2mm depending on the amount of stringing you experience. For other printers: the default retraction settings for PETG should be sufficient, but total retraction length may need to be increased slightly.
For Bambu Printers: It is recommended to lower your Top Surface print speed to 100-150 mm/s for higher top layer quality.
1kg Spool Dimensions (AMS-Compatible)
1kg Spool Dimensions (AMS-Compatible)
- Filament Weight = 1 kg
- Filament Diameter = 1.75 mm (+/- 0.05 mm)
- Spool Inner Diameter (ID) = 52 mm
- Spool Outer Diameter (OD) = 200 mm
- Spool Width (W) = 67 mm
- Spool Weight = 220 g
Share
In a Bambu Lab P2S using BL generic PCTG preset prints very nicely. I originally purchased the Obsidian Black to test. Every print cam out very nice and clean. I like the design of this filament it is not a sponge like PETG and I live in central Alabama where the summer humidity is oh so fun. This filament save me time and is always ready to go even in the summer. I like the toughness the fact that it can take the heat well and its not a sponge- Great afordable go to Filament for many projects.
Awesome color and it prints out so nice. Great layer adhesion
I tried to use it but never could get it to print right. Printed 10 Vororn cubes and they were all different and all different in size. Changed PA but couldn't get it as good as I have other filaments. Did everything except slow the print speed to 60mm/s, which is really a bit slow. Nozzle temp was 270, bed temp was 90. Great adhesion. Just tares and rough places in the print
I think it’s great wish you guys had a profile for either the elegoo slicer or orca slicer
This PCTG filament met all my expectations. Loaded the filament into my P1S with no drying, imported the Bambu profile provided by American Filament and this stuff just prints. The only change I made was to adjust the shrinkage to 99.4% and I am getting accurate tolerances for fitted parts. The finish is also pretty nice.