Filamento PLA+ Tough Pro AF negro ónix de 1,75 mm ¡Fabricado en EE. UU.!
Filamento PLA+ Tough Pro AF negro ónix de 1,75 mm ¡Fabricado en EE. UU.!
No se pudo cargar la disponibilidad de retiro
Presentamos nuestro nuevo PLA+ TOUGH Pro. Un PLA resistente de calidad de ingeniería que puede soportar fuertes impactos y altas temperaturas. Directamente desde la placa de construcción, nuestro PLA+ Tough Pro le brinda una resistencia al impacto 8,8 veces mayor que un PLA estándar.
Nuestro Tough Pro PLA+ utiliza resina virgen NatureWorks Ingeo 3D870, que fue diseñada para brindar propiedades térmicas y mecánicas similares al ABS en un paquete de PLA ecológico.
Este grado de PLA se puede recocer después de la impresión para cristalizar aún más el material, mejorando aún más sus propiedades térmicas y mecánicas.
Haga clic aquí para ver nuestra guía sobre cómo recocer sus piezas.
Nuestro Tough Pro PLA+ es un material verdaderamente resistente, diseñado para los trabajos más difíciles. Fabricado con resina PLA Ingeo 3D870 diseñada y fabricada aquí mismo en los EE. UU.; después del recocido, tiene una resistencia al impacto comparable al ABS y una resistencia a la temperatura comparable al PETG, todo en un paquete de PLA de base biológica con las mismas excelentes características de impresión 3D del PLA.
Cada carrete contiene 1 kg (2,2 libras) de filamento, con un diámetro de 1,75 mm y una precisión dimensional de +/- 0,05 mm.
Dimensiones del carrete (ahora compatible con las unidades AMS de Bambu Labs):
- Diámetro interior (ID) = 52 mm
- Diámetro exterior (OD) = 200 mm
- Ancho (An) = 67 mm
- Peso = 200 - 220 g
Recomendamos una temperatura de boquilla de 205-220 °C y una temperatura de lecho de 45-60 °C.
Anteriormente, Onyx Black se llamaba Matte Black. Si recibes un carrete con Matte Black en la etiqueta, ¡es el color correcto!
Descargas:
Print Settings
Print Settings
- Nozzle Temperature: 240 - 270°C
- Bed Temperature: 70 - 100°C
- Speed: 60 - 300 mm/s
Nozzle temperature can vary between 240-270°C depending on desired layer to layer adhesion vs part print quality. Higher nozzle temperatures will result in stronger parts, but may cause lower quality and/or increased stringing.
Part cooling can also vary depending on desired layer to layer adhesion vs part print quality. More cooling will result in better overhangs & bridging, but will decrease the ultimate layer to layer adhesion.
For Bambu Printers: We recommend using the Bambu Labs Gold Textured PEI build plate, or other aftermarket textured PEI build plates, for this material. 70°C should be sufficient for adequate build plate adhesion, going higher than this temperature may cause parts to adhere to the plate too well.
For Bambu Printers: recommended retraction length can vary between 0.8-1.2mm depending on the amount of stringing you experience. For other printers: the default retraction settings for PETG should be sufficient, but total retraction length may need to be increased slightly.
For Bambu Printers: It is recommended to lower your Top Surface print speed to 100-150 mm/s for higher top layer quality.
1kg Spool Dimensions (AMS-Compatible)
1kg Spool Dimensions (AMS-Compatible)
- Filament Weight = 1 kg
- Filament Diameter = 1.75 mm (+/- 0.05 mm)
- Spool Inner Diameter (ID) = 52 mm
- Spool Outer Diameter (OD) = 200 mm
- Spool Width (W) = 67 mm
- Spool Weight = 220 g
Share
This was my first roll of PCTG. It took a bit of set up but im fairly new to 3d printing so im sure some one more familiar with set up wouldn't have near the time invested. After i got it dialed in though this stuff has been amazing. It prints well, it holds up the the abuse on my RC dirt car and it has a nice shine to it. I run my plate at 60C and my nozzle at 260-265 with a travel speed of 40 mm/s. So far so good.
1st run with PCTG.
Impressive!
I put this on myrack a couple of weeks back and forgot about it while using up other material, you know how it goes. Up popped a project, wasn't really a yellow project, and I thought " can't learn it if you don't try it", box got opened and into service it went.
Didn't dry it (I KNOW, I KNOW! cut me slack, I didn't plan ahead), just dropped it in and went. Generic profile but bumped bed temp to 80, 230 nozzle, added a brim and hit go. Zero issues and the yellow! WOW! You can definitely see this in low light.
No issues
Arrived on time, package well sealed and reasonably dry. Prints so much better than PETG - great for functional prints.
I first clogged 3 heatbreaks before I found the correct parameters for my printer. But now the prints are just perfect. That material does (almost) not warp. The color is amazing.
This filament prints very well. I highly recommend American filament to anybody.